Best 15 how to build a staircase railing

Below is the best information and knowledge about how to build a staircase railing compiled and compiled by the lifefindall.com team, along with other related topics such as:: stair railing, how to build interior stair railing, diy wood stair railing, how to make a railing for stairs in minecraft, how to build a handrail for outdoor steps, build wood stair railing, indoor stair railings, handrails for stairs interior.

how to build a staircase railing

Image for keyword: how to build a staircase railing

The most popular articles about how to build a staircase railing

Stair Railing – myCarpentry

  • Author: www.mycarpentry.com

  • Evaluate 3 ⭐ (19973 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Stair Railing – myCarpentry On the front of the lower post, make a small mark at 32 1/2″ from the top of the tread on the first step. From that Upper Ref. Point (diagram [C]), mark the …

  • Match the search results: Stair railing should be required if your deck is 30″ (762 mm) or more above the ground. Always check your local building code before building a deck. The Prescriptive Wood Deck Construction Guide by the American Wood Council is an excellent source for deck building codes.

  • Quote from the source:

A Stylish DIY Stair Handrail For Your Home – Homedit

  • Author: www.homedit.com

  • Evaluate 3 ⭐ (15507 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about A Stylish DIY Stair Handrail For Your Home – Homedit The Step-by-Step to Build a DIY Indoor Stair Handrail · Materials needed for the black stair handrail project: · Part 1: Measure your stair …

  • Match the search results: This DIY stair handrail tutorial will take you through the step-by-step process of removing your old stair railing, building a new one, and installing as well as securing it.

  • Quote from the source:

3 Ways to Build a Handrail – wikiHow

  • Author: www.wikihow.com

  • Evaluate 4 ⭐ (37967 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about 3 Ways to Build a Handrail – wikiHow If you’re installing an indoor handrail, it will be mounted to the wall above the stairs. Wood is the most commonly used material for indoor handrails. It is …

  • Match the search results: Building a handrail is relatively easy if you have a basic tool kit and experience making home improvements. You’ll first need to measure the rise and run of your stairs to work out how long your handrail should be. You can buy premade handrails made of wood, metal, or synthetic materials in most ha…

  • Quote from the source:

DIY Staircase Railing | Tips & Tricks To Transform Your Home

  • Author: construction2style.com

  • Evaluate 3 ⭐ (14618 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about DIY Staircase Railing | Tips & Tricks To Transform Your Home Spindles · Handrails · Base trim · 1 x 6 · Lag bolts · Newel Posts (we made our own, but you can buy pre-made) · Wood glue · Wood filler …

  • Match the search results: So first, let’s check out the before. So long, golden oak staircase railing. 

  • Quote from the source:

Installing A New Stair Rail – DIY Railing Installation Guide

  • Author: extremehowto.com

  • Evaluate 3 ⭐ (5263 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Installing A New Stair Rail – DIY Railing Installation Guide Fill any hollow voids at the newel base with solid blocking and nail or glue into place. For final assembly, apply adhesive at all points of …

  • Match the search results: Home » Newest Articles » Stair Railing Installation – How To Install It Yourself

  • Quote from the source:

How to build a porch stair railing | HowToSpecialist

  • Author: howtospecialist.com

  • Evaluate 3 ⭐ (3265 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to build a porch stair railing | HowToSpecialist This step by step diy project is about how to build a porch stair railing. Building railings for the porch stairs is the last step of a complex backyard …

  • Match the search results: This step by step diy project is about how to build a porch stair railing. Building railings for the porch stairs is the last step of a complex and larger backyard project. Therefore, we strongly recommend you to check out the rest of the project, if you want to learn how to build a front porch from…

  • Quote from the source:

Stair Railings – Stair Parts – The Home Depot

  • Author: www.homedepot.com

  • Evaluate 4 ⭐ (38057 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Stair Railings – Stair Parts – The Home Depot Get free shipping on qualified Stair Railings products or Buy Online Pick Up in Store today in the Building Materials Department.

  • Match the search results:
    Reference #18.ad2e3717.1648915692.35484bb

  • Quote from the source:

Quick Guide: Stairs & Railings: Step-by-Step Construction …

  • Author: www.amazon.com

  • Evaluate 3 ⭐ (14837 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Quick Guide: Stairs & Railings: Step-by-Step Construction … Quick Guide: Stairs & Railings: Step-by-Step Construction Methods [Beneke Mr., Jeff] on Amazon.com. *FREE* shipping on qualifying offers.

  • Match the search results: Sorry, we just need to make sure you’re not a robot. For best results, please make sure your browser is accepting cookies.

  • Quote from the source:

How To Build A Distinctive Stair Rail – Fine Homebuilding

  • Author: www.finehomebuilding.com

  • Evaluate 4 ⭐ (30360 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How To Build A Distinctive Stair Rail – Fine Homebuilding Building stairs is a nice mix of design and build, and it’s a challenging job. This particular railing was for a set of housed-stringer stairs …

  • Match the search results: In my business, I wear a bunch of hats, including that of finish carpenter. Building stairs is a nice mix of design and build, and it’s a challenging job. This particular railing was for a set of housed-stringer stairs that I built. Most manufactured railing parts tend to have a formal, slightly gen…

  • Quote from the source:

DIY Stair Railing Makeover – The Painted Home by Denise …

  • Author: thepaintedhome.com

  • Evaluate 4 ⭐ (29854 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about DIY Stair Railing Makeover – The Painted Home by Denise … Stair Railing Makeover. If you’re interested in removing your old railings and replacing them, here’s the steps you need to take. 1. Choose the Style.

  • Match the search results: You can see why in the below photo. Hello 1980. Although this DIY stair railing makeover seems like a reasonable project for Tom and I to handle, we knew there would be some detail work that we’d need a more experienced carpenter for. We wanted the finish work to be perfect.

  • Quote from the source:

Build a Staircase Railing – DIYTyler

  • Author: www.diytyler.com

  • Evaluate 4 ⭐ (34755 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Build a Staircase Railing – DIYTyler Build a Staircase Railing. This project has been a long time coming! I honestly don’t even remember how long ago Sera and I went and picked up the stock.

  • Match the search results: Awesome job on the staircase railing! Its exactly what I have to do in my house. I still have to cut out the wall though. I dont know how hard that will be, but hope it goes well. I want to cut the stairs out, if you know what I mean, I dont want the railing to run on the wall, on the bottom. I woul…

  • Quote from the source:

Quick Answer: How To Build A Stair Railing – SeniorCare2Share

  • Author: www.seniorcare2share.com

  • Evaluate 3 ⭐ (6517 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Quick Answer: How To Build A Stair Railing – SeniorCare2Share What is the difference between a stair rail and a handrail? What type of wood is used for deck railings? Are balusters and spindles the same thing? How do you …

  • Match the search results: Handrail Dimensions A railing attached to a wall must be at least 1¼ inch and no more than 2 inches thick. The support brackets must hold the railing at a distance of at least 1½ inches from the wall and project a maximum of 3½ inches from the wall. The surface of a railing must be smooth, with no s…

  • Quote from the source:

How to Build Wood Stair Railing | DoItYourself.com

  • Author: www.doityourself.com

  • Evaluate 4 ⭐ (36840 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Build Wood Stair Railing | DoItYourself.com How to Build Wood Stair Railing · Step 1 – Start the Building Job · Step 2 – Take the Measurements · Step 3 – Join the Post and the Railing · Step 4 …

  • Match the search results: Fasten a clamp to the 2 x 4 plank and attach the measuring tape to the carpenter’s level in order to calculate the distance between the second stair and the wooden railing. Use some other clamps to hold the railing from its end (from the wall or the ceiling) and make sure the height of the rai…

  • Quote from the source:

How to build a railing for deck stairs – The Washington Post

  • Author: www.washingtonpost.com

  • Evaluate 3 ⭐ (4990 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about How to build a railing for deck stairs – The Washington Post This deck stair railing was made using great skill and modular parts … I read your recent column about building stairs for a deck.

  • Match the search results: Calculating the angle of the cut for the railings is very simple. Once you have your railing posts in position and secure, you just clamp your bottom rail to the posts with the excess railing extending past the posts. Be sure the bottom railing is at least 1 inch above the tips of the stair nosings …

  • Quote from the source:

Stairs and Stair Parts – B&Q

  • Author: www.diy.com

  • Evaluate 4 ⭐ (34380 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Stairs and Stair Parts – B&Q Discover different types of stairs and stair parts from oak handrails to space saving stair case designs for homes with more restrictions on space.

  • Match the search results: Discover different types of stairs and stair parts from oak handrails to space saving stair case designs for homes with more restrictions on space. For quick repairs you'll find a wide range of stair parts to match the look and feel of your existing stairs. We also offer complete banister and l…

  • Quote from the source:

Multi-read content how to build a staircase railing

DIY Custom Staircase Railing

If you have an old stair railing that needs replacing or updating, I’ve created a guide on how to build and install a custom stair railing for your home.

Depending on the type and size of your home, your staircase configuration may differ from what is in this guide, but the concept of building a stair railing will be the same. You can easily modify these plans according to your needs and the configuration of your stairs.

In this guide, I will walk you through how to install a stair handrail for a two-stair home. The first horizontal section is above the stairs and the second section starts with a horizontal slab and then descends the stairs.

You might also be interested in my other living room projects likeDo-it-yourself window shuttersandReclaimed wood frame sign.

DIY Custom Staircase Railing

Completion time

16 hours

total cost

$600

Competence level

Advanced

PDF Custom Stair Railing

$0.00

This PDF download includes a cut diagram, materials list, and 3D illustration with detailed steps for building the project. Measurements are in UK metric not metric. SketchUp/CAD files are NOT included.

Custom stair railing

This PDF is free, but if you’re feeling generous today, can you give me a little advice to help me create more projects. Thank you!Advice

– WHERE – Free PDFs

Tools for this project

  • cord
  • Drill
  • Miter saw
  • saw table
  • Nailer
  • Kreg Jig
  • Sanders
  • wood router

Equipment list

  • Post 4×4 (x5)
  • 2x4x10 (x4)
  • 2x4x8 (x1)
  • 1.5×0.25×10 (x3)
  • 1x2x10 (x17)
  • 1x2x8 (x1)
  • 1x4x10 (x2)
  • 1x6x10 (x2)
  • 2 1/2 pocket hole screw
  • Wood glue
  • 2 brad nails
  • 1 Brad Nails
  • 4″ wood screw

Note: Timber sizes listed are nominal sizes. See timber dimensions for actual and nominal sizes.

Disclosure: Some of the links on this page as well as those in the “tools for this project” and “list of materials” sections are affiliate links.

Cut

dimensions for diy staircase railing

Cutting list

cut list for diy staircase railing

cut list for diy staircase railing

Step 1 – Cut the Post for the Stairs

When designing and building handrails for stairs, you must first determine where to place the posts. Posts must be securely fastened to the stairs or wall to support the weight of the rails.

For this project, I’m using a 4×4 poplar column commonly used for stairs. The actual width and depth of the 4×4 post is 3 1/4″ x 3 1/4″. This is different than if you were to use conventional 4×4 lumber measuring 3 1/2″ x 3 1/2″.

Take the 4×4 poplar poles and cut three 38″ pieces. Then cut a 42″ long piece and a 52″ long piece. Take one of the 38″ pieces and rip it in half with a table saw. This half-cut post will be used in the wall track segment.

After cutting all the posts, use the Kreg Jig to drill small holes in the bottom of the 38″ and 42 posts. The Kreg jig should be set for 2 ½” hole screws. No holes are required in half-cut or 52″ posts.

cutting posts for diy staircase railing

drilling pocket holes in post for railing

pocket holes drilled in the posts

Step 2 – Measure and Cut the Base Mold for the Posts

The bottom end of each pole will have a molded base around it to make it look better and to cover the holes in the bag. These plywood panels are usually made from MDF panels, like crown moldings and baseboards. You can buy these boards already painted white.

Take the 1×4 and 1×6 MDF boards and cut the base pieces as shown in the cut list. These plywood boards will be attached to the posts once everything is painted.

cutting base moulding for diy staircase railing

Step 3 – Cut Handrails and Base Rails for Cross Section

For the base rails and handrails I used 2×4 redwood sawn 2 ½” wide. The 2×4 itself is already too wide for the handrail, so reducing it to 2 ½” wide seems much better.

Take the redwood 2×4 and cut two pieces 56 3/4″ long and one 36 1/4″ long for the top rail of the horizontal section. Then, using a table saw, cut these boards to a width of 2 1/2″.

The base rails will be slightly shorter as the base is molded around the pylons. For the base rail, cut two pieces 55 1/4″ long and one piece 34 3/4″ long, then cut them 2 ½” wide.

Then take the 1 ½” x” thick board and cut two pieces 56 3/4″ long and the other 36 1/4″ long. This ¼” thick plank will be placed on top of the guardrail plate with the guardrails attached to this plank. The handrail will then be placed on this ¼” board and nailed from the bottom.

Using the Kreg jig, drill holes in the top of each handrail and handrail. Kreg Jig should be configured for 2 1/2″ holes.

cutting upper and lower rails for diy staircase railing

Step 4 – Measure and Cut Handrail for Slope

The rail ramp must be cut at an angle at both ends. This angle may vary depending on the slope of your stairs but for this project the angle was 42 degrees.

Similar to Step 3, take the 2×4 redwood and cut the base rail to 104 1/8″ with a 42 degree miter cut on both ends. Next, cut the railing and 1/4″ thick board to a length of 106 1/8″ with a 42 degree cut. Next, rip these two 2×4 boards 2 1/2″ wide and drill holes in both ends of the handrails.

sloped rail for diy staircase railing

Step 5 – Cut the Balusters for the Horizontal Section

When cutting bundles of film, it is important to make them all exactly the same length. Use a stop block on your chainsaw to make sure the length is perfect.

Take a 1×2 poplar board and cut 39 pieces of baluster to a length of 29 3/4″. These pieces will be used for the horizontal portion of the stair handrail.

balusters for diy staircase railing

cut balusters for diy staircase railing

Step 6 – Cut Balusters for Sloped Roof Section

Similar to Step 5, the ramp attachment segments also need to be the perfect length, so use a block on your chainsaw.

For the steep part of the staircase, the railings should be cut at a 42 degree angle at both ends. Use the same 1×2 poplar board and cut 22 beams to 30 1/2″ length.

cut balusters for the sloped section of the diy staircase railing

using stopper to cut balusters

Step 7 – Create a Spacer Jig to Attach the Joist

When attaching rail assemblies to the top and bottom rails, you must ensure that they are completely straight and the same distance apart. Having evenly spaced clusters makes the whole project look great. To do this, you will need to create spacers that you can place between the assemblies to ensure equal spacing.

Since some assemblies are spaced 2″ apart and others 4″, you will need two spacers for the horizontal sections and two spacers for the angled sections.

Take 3/4″ plywood or scrap wood and cut one piece into 2 3/4″ x 2 ½″ and another into 4 3/4″ x 2 ½″. Next, cut out a jigsaw “x 1 ½” with a jigsaw on both pieces. See pictures. These spacers will be used for the horizontal part of the rail.

Now the spacers for the tilt should be cut on both sides at an angle of 42 degrees. To keep things simple, ¾” x 1 ½” notches are not required for these stamps, although you can create some if you wish. Cut one spacer at 5 1/4″ and the other at 2 5/8″ with 42 degree angles on both sides.

spacer jigs for attaching balusters

making a spacer jig for diy staircase railing

spacer jig make for balusters

Step 8 – Round the Corners of the Bottom and Top Rails

Since the bottom and armrests have been ripped to a shorter width, the ripped side will have sharp corners and the unripped side will have rounded corners. To make them all the same, take a wooden router and go through sharp corners with a circular router. This will make all corners rounded.

rounding edges for handrails

Step 9 – Attach the Beam Bal to the Bottom Rail of the Horizontal Section

Find the center of the bottom rail and make a small pencil mark. This will be the location of the first baluster. Apply wood glue to the bottom end of the shield, then center it and nail it with a 2″ finish nail. Now place a 2″ spacer above the first installed baluster, then insert the baluster into the groove and secure it with finishing nails.Repeat the process for the remaining baluster using spacers.

Assemblies should be mounted in pairs 3 2 inches apart. Then there will be a 4 inch gap between the next pair of triplets. Finish the remaining pieces attached to the bottom rail with wood glue and finishing nails.

attaching balusters to the bottom rails

attaching balusters to bottom rail

pocket holes in the bottom rails

Step 10 – Glue and Secure Thick Wood Strips to Industrial Clusters

The main purpose of the ¼” thick wood strip at the top of the rail is to hide the nails. If you don’t have this piece, you will need to attach the nail beams directly to the railing with nails from the top, which will expose the nail.These nails can be coated with wood filler but it is a lot of work and it may still leave a small nail mark.So instead of nailing the top railing to the fences you will need to first lay down a ¼” thick strip of wood. Then the top railing will be nailed to the strip from bottom to top to hide the nails.

Attach the very similar ¼” thick strip of wood to the bottom rail. Again, find and mark the center of the strip, then attach it to the balls using wood glue and 1″ nails. Use the same spacers to ensure that the assemblies are aligned.

attaching top rail for the diy staircase railing

horizontal stair panel

Step 11 – Assemble the Ramp

Mounting the inclined track section is similar to the horizontal one. First, find and mark the center of the bottom rail. Then, instead of attaching a stamp in the center (as we did in the horizontal part), we will have a 5 1/4 space in the center of the marker. Then attach the shield to each side of the spacer. Continue mounting the rest of the fan to the bottom rail. Finally, attach the 1/4″ thick strip of wood, then the top rail.

assembling sloped rail for diy staircase railing

attaching balusters to bottom rail

connecting balusters together for sloped section

Step 12 – Paint All Parts

Now that you’ve cut all the pieces and assembled the track plates, it’s time to paint. Use a paint sprayer to paint evenly. You may need to spray several coats to make it look good.

painting stair railing for diy staircase railing

Step 13 – Install Half Post to Wall

It’s time to install the rails. Starting from the wall, first attach the half post to the wall using 4″ wood screws. The 4″ screw must be attached to the wall screw or the rail will loosen over time.

Verify that the position is granted. Drive in the two screws at the bottom of the post below the 18 inch mark as the cast base is 18 inches high and will cover the screws. Then drive in the third screw 35″ from the bottom. Once the stair handrail is installed, this screw ends behind the handrail. We wanted to cover the screws or nails as much as possible.

attaching post to the wall for diy staircase railing

attaching post to the wall

Step 14 – Wrap and Nail Base Mold Around Post

Now that the first post is securely fastened to the wall, attach the cast iron base to the bottom of the post using 1 1/4″ dowels. See pictures.

attaching base moulding to the post

wrapping post with base moulding

Step 15 – Post Railing Panel

Take the first horizontal plate and secure it to the post using 2 1/2″ hole screws in the bottom rail. Rails should be mounted 3″ from the bottom of the post. You can use 3-inch-high blocks to place the panel, which makes installation easier.

Place the handrail on top of the 1/4″ thick board and secure it with 1″ finish nails. Then use 2 1/2 hole screws to secure the handrail to the post.

attaching stair rail panel to the post

connecting horizontal stair rail panel

Step 16 – Install Remaining Posts and Rail Panel

Take the next 38″ post and attach the base moldings to both sides without the pocket holes. Then place this post against the first panel and attach it to the pony wall using 2 1/2″ hole-pocket screws. Then thread the holes through the recess in the top and bottom rails to attach the board to the post. Cover the back pocket holes with molds.

Repeat the process to install the following rail plates and posts. The downward sloped panel will not be raised 3 inches.

diy staircase railing

attaching horizontal railing for stairs

attaching handrail to the post of the diy staircase railing

attaching post to the pone wall with pocket hole screws

attaching sloped section of the diy staircase railing

Step 17 – Cover Pocket Hole

To seal the holes in the handrail and bottom rail, take a 3/8″ wooden dowel and cut it into small pieces about 2″ in length. Then close the peg in the pocket hole. Using a horseshoe saw, cut off the rest of the protruding pin. Polish the bar and even it with the rails. Then use a top coat to cover the wood. You are done with the custom DIY stair railing.

DIY Custom Staircase Railing

Popular questions about how to build a staircase railing

How do you build an indoor stair railing?

How do you build stair railings?

How do you build a wooden stair railing?

How do you make a simple handrail?

How do you make a removable stair railing?

How long should a stair rail be?

Measuring Handrail Length

ADA compliant stair handrails, mandatory in commercial settings, must run the full length of the Nosing Line. In addition, they require a 12” horizontal section at the top, starting at a point directly above the upper nosing.

How do you attach a banister to the wall?

How do you make a banister sturdy?

Replace the old hardware with new bolts or lag screws, depending on what you removed. Tighten well to make the stair railing sturdier. Apply a bead of heavy duty glue to any areas that are wiggling but that do not have hardware, such as where the balusters meet the railing.

What angle do you cut stair railing?

45-degree angle
Start by cutting a 45-degree angle on one end of the stair railing and rest this end on the floor. This cut is for the short return to the wall.9 thg 8, 2019

How do you build a stair bannister?

Can I use 2×10 for stair treads?

It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.

How far apart should stair spindles be?

4 inches
Balusters are the vertical guards that support the handrail. They must be installed close enough that the space between them is less than 4 inches. Most city inspectors carry a 4-inch ball with them to test the spacing. Installed balusters should withstand 50 pounds of pressure exerted over a 1-sq.

What size wood is used for stair stringers?

2x12s
Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.

Can I use a 2×4 for a handrail?

According to the IRC (2018), you can use a 2×4 to make a handrail, but you must cut finger recesses along both sides of the board and position the lumber lengthwise on its end. Using a 2×4 as a handrail laid vertically is not allowed. Porch and deck guardrails made from 2x4s laid horizontally are permitted.

How do you build a rail?

Video tutorials about how to build a staircase railing

keywords: #anawhite, #woodworking, #build, #wood, #plans, #project, #howto, #howto, #how-to, #diy, #doityourself, #doityourself, #do-it-yourself, #easy, #simple, #2×4, #freeplans, #make, #tutorial, #Staircase, #Railing, #Stair, #Handrail, #Guardrail, #Staircaserailing, #Stairrail, #Handrail, #Guardrail, #Rail

Very DIY friendly staircase railing method. No welding or special tools. Inexpensive materials. Looks amazing! More information at

-https://www.ana-white.com/woodworking-projects/modern-farmhouse-diy-staircase-railing

CHECK LOCAL BUILDING CODES BEFORE DESIGNING STAIRS

keywords: #howtobuildarailingforsteps, #howtobuildarailingforindoorstairs, #howtobuildabannister, #buildindoorrailing, #howtobuildastairrailing, #buildinteriorrailing, #howtobuildarailingonstairs, #howtobuildabanisterrailing, #buildbannister, #buildbanister, #buildstairrailing, #buildbaluster, #buildstairbanister, #howtobui;d, #howtobuildabanisteronastaircase, #buildhandrail, #Handrail, #diystairrailing

Today I use some red oak to make a beautiful DIY railing for our staircase.

Get your Shirt on!!

-http://bit.ly/DITylerMERCH

Write up with more pictures:

-http://diytyler.com/build-a-staircase-railing/

I found a lot of guidance for this project from John Heisz’ website, check out the article about his railing here (

-http://www.ibuildit.ca/other%20projects/Home%20Improvement/stair-railing-1.html)

John Heisz IBuildIt Youtube Channel:

-https://www.youtube.com/user/jpheisz

Subscribe for more DIY videos

-http://bit.ly/2UJxXZW

Follow us on Instagram

-http://instagram.com/diytylerg

“Cipher” Kevin MacLeod (incompetech.com)

Licensed under Creative Commons: By Attribution 3.0

keywords: #StairHandrail, #Handrail, #HowtoInstall, #Install, #buildstairs, #stairs, #build, #Howto, #Howtobuild

How to build stairs: The Handrail. Basic Stairbuilding Course

-https://lowesvideo.com/course/60

keywords: #BuildRusticStairRailing, #DIY, #Rustic, #Ron.Hazelton, #HouseCalls, #stairs, #railing

Add Protective Stair Railing to an Existing Staircase while Preserving the Rustic Character of Its Heavy Pine Construction

Stay in step with the rustic character of your existing staircase by adding wood stair railing that mirrors its heavy pine construction. Assembled with groove-and-tenon joints and dowels, the sturdy handrail and square balusters of this simple project’s design complement the roughhewn staircase while adding safety for young and old, alike.

Home Improvement Online With Ron Hazelton

With over 500 hundred free DIY ideas, tips, how-to’s, suggestions, and video tutorials available to help you turn your home improvement plans into finished projects. With more projects being added every month this is the go-to place for Do-It-Yourselfers \u0026 professionals alike.

_____________

Check Out Our Site:

-http://www.ronhazelton.com

Follow Us On Twitter:

-https://twitter.com/ronhazelton

Like Us On Facebook:

-https://www.facebook.com/RonHazeltonHouseCalls

Follow Us On Google+:

-https://plus.google.com/u/1/b/106595458746638326576/+ronhazelton/posts?pageId=106595458746638326576

View Our Pinterest:

-https://www.pinterest.com/ronhazelton/

Don’t Forget To Subscribe:

-https://www.youtube.com/channel/UCT7uKjjnhi3eozGVrjKfTzQ?sub_confirmation=1

See more articles in category: FAQs