Best 13 how to replace under sink plumbing

Below is the best information and knowledge about how to replace under sink plumbing compiled and compiled by the lifefindall.com team, along with other related topics such as:: under sink plumbing diagram, replacing drain pipes under kitchen sink with garbage disposal, how to replace water pipes under kitchen sink, under sink plumbing parts, how to replace pipes under bathroom sink, how to install double kitchen sink plumbing, replace sink drain pipe in wall, under kitchen sink plumbing.

how to replace under sink plumbing

Image for keyword: how to replace under sink plumbing

The most popular articles about how to replace under sink plumbing

Replacing Kitchen Sink Pipes – Home Guides

  • Author: homeguides.sfgate.com

  • Evaluate 3 ⭐ (8356 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Replacing Kitchen Sink Pipes – Home Guides Replacing Kitchen Sink Pipes · 1. Put a bucket under the curved portions of the P-traps and turn the water valves off so you don’t get soaked if someone runs the …

  • Match the search results: The pipes under your kitchen sink can look daunting, especially if you have two sinks, but it’s easier than you think to replace a sink drain pipe, even if you have little plumbing experience. The curved pipes, which are called P-traps, connect to the sink drain and waste lines by compression fittin…

  • Quote from the source:

How to Replace Pipes Under Kitchen Sink? Easy and Simple …

  • Author: www.kitchenrank.com

  • Evaluate 4 ⭐ (30260 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Replace Pipes Under Kitchen Sink? Easy and Simple … How to replace pipes under kitchen sink and what we need · Step 1: Remove Existing Pipes · Step 2: Prepare the New Drains before you proceed with the rest of the …

  • Match the search results: Filed Under: Blog Tagged With: how to connect pipes under sink, how to install a kitchen sink drain pipe, how to install pvc pipe under kitchen sink, how to install sink drain pipe, pipes under kitchen sink diagram

  • Quote from the source:

How to Replace a Sink Pipe | HEB Plumbing & Sprinkler

  • Author: hebplumbing.net

  • Evaluate 4 ⭐ (24478 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Replace a Sink Pipe | HEB Plumbing & Sprinkler How to Replace a Sink Pipe · Step 1: Preparing the Space · Step 2: Dismantling the Pipes · Step 3: The Drain Tailpieces · Step 4: Install the New …

  • Match the search results: A leaking sink pipe can create a slew of problems for your home. Excess water can result in mold, a damaged sink cabinet, damaged materials, and a higher water bill. It is essential to get the faulty sink pipe replaced as soon as possible to reduce the amount of damage caused by the leak. If you are…

  • Quote from the source:

Kitchen Sink Installation Step-by-Step Guide – This Old House

  • Author: www.thisoldhouse.com

  • Evaluate 4 ⭐ (34432 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Kitchen Sink Installation Step-by-Step Guide – This Old House Measure and Mark the Kitchen Sink’s Layout · Mark the Cut Lines onto the Counter · Cut a Sink Opening with a Jigsaw · Install Kitchen Faucet · Attach Strainer Over …

  • Match the search results: The trickiest part of installing a new sink and faucet is connecting the sink’s drain—the pieces between the sink’s tailpiece and the waste line. Always start at the sink tailpiece and work down. This is where a swivel P-trap with a trap adapter earns its keep. It can swing side to side on two diffe…

  • Quote from the source:

How to Replace a Kitchen Sink | Definitive Guide | My Plumber

  • Author: my-plumber.co.uk

  • Evaluate 4 ⭐ (21547 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Replace a Kitchen Sink | Definitive Guide | My Plumber Step 1. Fit your new sink and seal it in place · Step 2. Attach the metal sink clips and fit your faucet · Step 3. Seal and fasten the drain strainer · Step 4.

  • Match the search results: Next, you have to unscrew the metal clips. They are located underneath the sink for both top and under-mount sinks. After you remove the clips, you need to cut the caulk. The difference between the two types of sinks is caulk’s location. For under-mount sinks, it’s located underneath the sink where …

  • Quote from the source:

Under Sink Plumbing at Lowes.com

  • Author: www.lowes.com

  • Evaluate 3 ⭐ (17339 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Under Sink Plumbing at Lowes.com Find under sink plumbing at Lowe’s today. Shop under sink plumbing and a variety of plumbing products online at Lowes.com.

  • Match the search results:
    Reference #18.9f2e3717.1648902105.a10dd7

  • Quote from the source:

5 Steps To Replace Pipes Under Kitchen Sink – | Tips, Tricks …

  • Author: howtoimprovehome.com

  • Evaluate 3 ⭐ (7992 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about 5 Steps To Replace Pipes Under Kitchen Sink – | Tips, Tricks … The simplest way is to get new pipes and nuts, then remove all old fixtures after proper identification. Attach a new drainpipe by taking its thread and fixing …

  • Match the search results: There’s also a gasket, retainer, and washer under the sink. The retainer serves as a nut that connects the sink to the body. Also, the sink has a tailpiece that connects to the strainer through threads. The tailpiece is a significant component of the drain trap and is connected by slip nuts. Y…

  • Quote from the source:

Replace kitchen sink drain plumbing | Phá.vn

  • Author: xn--ph-nia.vn

  • Evaluate 4 ⭐ (39807 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Replace kitchen sink drain plumbing | Phá.vn Top 17 ✓ Replace kitchen sink drain plumbing được cập nhật mới nhất lúc … how to replace drain pipe under sink , are kitchen sink drains …

  • Match the search results: Top 17 ✅ Replace kitchen sink drain plumbing được cập nhật mới nhất lúc 2022-02-10 00:21:41 cùng với các chủ đề liên quan khác , replace kitchen sink drain plumbing
    , installing kitchen sink drain plumbing
    , how to replace drain pip…

  • Quote from the source:

Plumbing Systems Repair Cost Guide – Your Super Inspector

  • Author: yoursuperinspector.com

  • Evaluate 3 ⭐ (5489 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Plumbing Systems Repair Cost Guide – Your Super Inspector Repair Leaking Faucet: $175 – $400 · Replace Kitchen Sink Faucet: $300 – $800 and up · Replace Bathroom Faucet: $250 – $500 · Replace Exterior Faucet: $150 – $300 …

  • Match the search results: Texas Real Estate Commission License #6810
    Certified Applicator License #41794
    Texas Association of Real Estate Inspectors (TAREI)
    Greater Denton/Wise County Realty Association
    CCAR – Collin County Association of Realtors
    TREC Instructor Blake Williams # 3398
    TREC Instructor Jeff Howell # 22020

  • Quote from the source:

How to Replace A Kitchen Sink | PlanItDIY

  • Author: www.planitdiy.com

  • Evaluate 4 ⭐ (26840 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Replace A Kitchen Sink | PlanItDIY Remove the slip nut and gasket connecting the drain assembly to the floor pipe. How to Replace Your Kitchen Sink – Step 7. Under the sink, loosen the clamp …

  • Match the search results: Now turn the sink upside down and run a bead of silicone caulk around the outer edge of the sink. Carefully turn the sink over and place it in the hole. Some of the caulk should seep out the edge between the sink and the countertop. Wipe this clean with a rag.

  • Quote from the source:

How to Replace A Kitchen Sink | PlanItDIY

  • Author: www.planitdiy.com

  • Evaluate 4 ⭐ (20760 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about How to Replace A Kitchen Sink | PlanItDIY Remove the slip nut and gasket connecting the drain assembly to the floor pipe. How to Replace Your Kitchen Sink – Step 7. Under the sink, loosen the clamp …

  • Match the search results: Now turn the sink upside down and run a bead of silicone caulk around the outer edge of the sink. Carefully turn the sink over and place it in the hole. Some of the caulk should seep out the edge between the sink and the countertop. Wipe this clean with a rag.

  • Quote from the source:

Do Plumbers Install Sinks? – Flow Pro Plumbing

  • Author: www.flowpro-plumbing.com

  • Evaluate 4 ⭐ (35051 Ratings)

  • Top rated: 4 ⭐

  • Lowest rating: 2 ⭐

  • Summary: Articles about Do Plumbers Install Sinks? – Flow Pro Plumbing Today, we’re here to definitely answer that question: plumbers can and regularly do install sinks. In fact, we highly recommend that you have a …

  • Match the search results: If you have a garbage disposal or dishwasher, you’ll also need to disconnect those. After all, lines are disconnected, loosen the metal clips under the sink, cut the caulk around the sink and slowly push the sink out to remove it.

  • Quote from the source:

Replace kitchen sink drain plumbing | Xu-hướng-seo-2022.vn

  • Author: xn--xu-hng-seo-2022-d8d3508j.vn

  • Evaluate 3 ⭐ (17274 Ratings)

  • Top rated: 3 ⭐

  • Lowest rating: 1 ⭐

  • Summary: Articles about Replace kitchen sink drain plumbing | Xu-hướng-seo-2022.vn Anti-slip Kitchen Sink Repair Wrench Set Plumbing Water Heater … Mesquite Plumbing – Trang chủ | Facebook; All About Plumbing Plumber Sink …

  • Match the search results: Top 17 ✅ Replace kitchen sink drain plumbing được cập nhật mới nhất lúc 2022-02-10 00:21:41 cùng với các chủ đề liên quan khác , replace kitchen sink drain plumbing
    , installing kitchen sink drain plumbing
    , how to replace drain pip…

  • Quote from the source:

Multi-read content how to replace under sink plumbing

House

How to replace a kitchen dish rack and an old metal trap

Updated: May 20, 2019

Remove a leaky chrome kitchen drainpipe and replace it with a PVC drainpipe and trap.

Next projects

man shines light on under sink pipes

From the DIY experts at Family Handyman magazine

You May Also Like: TBD

Timea perfect day
ComplicationIntermediate
AssessLess than $20

How to install kitchen sink plumbingStep 1:Straighten the kitchen sink water lines and tighten the nuts

Straighten bent pipes
Loosen the slip nuts, then straighten the bent pipes. Tighten the metal nuts with slip joint pliers. With plastic nuts, it is recommended to tighten by hand first. If this does not stop the leak, gently tighten the nut with pliers.

Sealing washers on pipe joints will not hold water unless one section is directly inside the other. The “ground” gasket on the trap has no washers, but it will also leak if misaligned. Flash the leaking gasket to check its alignment. If it is bent, simply loosen the nut, straighten the pipe and screw it back on. Because the entire assembly is interconnected, you can misalign one joint while manipulating another. Don’t be surprised if you end up loosening and tightening several joints to straighten just one.

If a gasket is aligned but still leaking, tighten the slip nut. Use pliers to tighten two slip joints on the metal pipe: one to hold the tube, the other to tighten the nut. If you have an old metal tube, you may find that it has worn down and deflated when you put a pair of pliers on it. With plastic pipes, the hand must first be tightened. If that doesn’t stop the leak, use a pair of pliers. But be gentle; Plastic only easy to strip.

Find a leak in the sink pipes

Before you can stop a leak in your kitchen sink plumbing, you need to find its source. It can be difficult. Water coming out of your pipes can travel a long distance before it hits the floor of your cabinets.

Here’s how a detective searches for the source of the leak: Pour warm, not cold, water into both sink bowls. (Cold water can cause condensate particles to build up on the pipes, making it difficult for you to find the leak.) Next, stand under the sink with the fault light on. Dry all the pipes and check the seals around the basket filter. If you don’t see any drips forming, remove both sink plugs and watch the drips tell the tale.

Joints are the most likely source of leaks, but old metal pipes can develop pinhole leaks anywhere, especially in traps. If you find no leaks in the drainage system, check the water supply lines serving the faucet. Finally, check for “splash leaks,” where water seeps under the sink rim or faucet base. To find these leaks, dip a rag around the sink faucet and rim, then go underneath and look for water droplets.

How to install kitchen sink plumbing2nd step:Repair a leaking filter

How to install the sink drain hose Photo 1: Dismantling the drain hose
Remove the drain assembly from the sink so you can remove the leaking strainer. Turn the nut counterclockwise, using a second set of pliers if necessary to keep the pipes from turning.How to install the sink drain pipe Photo 2: Remove the filter
Turn the locking pin counterclockwise to remove the filter. Have an assistant insert the handle of the pliers into the holes in the strainer and secure the strainer from turning with a screwdriver.How to install the sink drain pipe Photo 3: Cut the handle lock if it will not be removed
Cut the loop with a hacksaw if you can’t pull it out. Cut at an acute diagonal angle and be careful not to cut into the sink.How to install a sink drain pipe Photo 4: Place plumber’s putty around the drain hole
Roll plumber’s putty on a string and surround the drain hole. Install the rubber washer and cardboard washer and tighten the lock using the same method you used to remove the old washer.

The main gasket around the basket strainer is a plumber’s putty, which doesn’t last forever. Over the years it can harden, shrink or crack. Sometimes you can prevent a leak by tightening the lock. But in many cases, the only cure is a fresh dose of powdered medicine.

Images 1-4 above show you how. You can reuse the old filter if all parts are in good condition, but you must replace it. Since you have to remove most of the drain assembly to remove the leaky strainer (Picture 1), consider replacing the sink drain lines if they are old.

The hardest part of this job is removing the old set screw, which is often spot welded due to mineral deposits or corrosion. A special key designed only for locks is called an “adjustable key” or “lock key” (Picture 2). Large sliding pliers with a 3-1/2 inch jaw opening will also work, and you can use them for other jobs. No matter what tool you use, you can see that the lock won’t budge. In this case, a hacksaw cut is the only solution (Image 3). It’s nearly impossible to do this without cutting the filter wires, so plan on buying a new one.

Figure A: Basket Filter

This photo shows the washers and loops connecting the basket

How a strainer connects to a tailpiece

How to install kitchen sink plumbingStep 3:If the sink water pipe is old, replace the entire building

How to install the dishwasher drain hose Photo 1: Connect the drain hose to the filter
Attach the rear unit to the basket strainer, but do not fully tighten it; you will have to remove and cut it later.How to install the dishwasher drain hose Photo 2: Place the hand trap under the drain hose
Slide the trap handle into the adapter. Then attach the trap and slide the arm in or out to position the trap just below the tail. You may need to cut the arm or add an extension.How to install sink drain pipe Photo 3: Mark and cut details to fit size
Hold the drain tee along the drain pipe about 1-1/2 inches below the top of the trap. Mark the tail 1/2 in. Under the top of the tee. Cut both ends to the same length and tie them off.How to install the sink drain pipe Photo 4: Mark and cut the swing arm
Slide the swingarm into the second exhaust, extending about 3/4 inch into the crown and mark. Cut it and install it.How to install the sink drain pipe Photo 5: Tilt the drain arm up to the drain
Loosen the slip nut and slide the T-bar up or down so the swingarm tilts slightly toward the T. Tighten all nuts.

Some sink plumbing leaks cannot be prevented by tightening or tightening. Stripped nuts won’t tighten and old washers won’t seal because they’re stiff and warped. You can buy new nuts, washers or drainers. Since plastic pipes are so cheap and easy to install, the smart and reliable solution is to assemble a brand new drain pipe.

You can buy everything you need at the visitor center. Kits for the side outlet assembly (as shown here) or the center outlet assembly (where the trap is located below the center of the sink) contain most of the essential parts. But you may also need:

  • The tail is long (Photo 1). The parts that come with the kits are usually only a few centimeters long.
  • A hatch arm extension (Photo 2). The arm supplied with the kit may not reach the drain pipe protruding from the wall.
  • The star dishwasher is connected to the faucet of your dishwasher.
  • A waste disposal kit that allows the swingarm to connect to the waste disposal. Pictures 1-5 describe the whole replacement process in detail.

Here are some suggestions for a smooth project:

  • We will have to cut a few pipes: the exhaust, the exhaust, and possibly the siphon. A serrated hacksaw works best.

If in doubt, mark and cut the pipes slightly. Better to cut twice than to cut too short and make an extra trip to the hardware store.

  • Don’t forget to attach the lens collar (Photo 1). Other seals require conical washers. The only washerless connection is the ground connection at the trap.
  • Assemble everything loosely until the set is complete. Then tighten all the sliding nuts.
  • Tighten the slip nuts by hand. If any seals leak when testing the new assembly, tighten them lightly with non-slip pliers.
  • When you’re done, check the assembly for leaks.

Figure B: Complete Assembly Replacement

This photo shows the parts needed to connect the filter to the waste swing arm. For a larger image that also shows the trap and trap arm, see the appendix.

Strainer connected to the waste arm

Point:

Apply a little Teflon tube lace glue to the men’s shoelaces. It lubricates the threads and greatly facilitates the tightening of sliding nuts. Check the label to make sure the sealant is safe for plastic.

How to install sink plumbing Step 4:Install the new adapter on the old steel pipe

Use the coupler to connect to the drain hose
A rubber connector connects the PVC pipe to the steel drain pipe.

The drain hose that comes out of the wall has an adapter on its end. This adapter has a slip washer and nut and works just like the other gaskets in your drain assembly. If your drain hose is plastic, you should have no problems. But if your drain pipe is old galvanized steel, you may have corrosion that makes it nearly impossible for the nut to slip or tighten.

Here’s how to get rid of those rusty old threads: Remove the old slip nut. Cut it with a hacksaw if necessary, but try not to cut deep into the threads of the drain pipe. Purchase a plastic trap adapter, a rubber transition coupler, a piece of plastic and cement pipe. Hoses and adapters can be PVC (white) or ABS (black); just make sure you get the right cement for the plastic (PVC also requires a purple primer). 4 in. cement adapter. pipe and connect the plastic pipe to the old metal pipe using a rubber coupling.

Additional information for pipes under the sink

  • Explosive images of the drainage system

Tools needed for this kitchen sink plumbing installation project

Get the tools you need for this do-it-yourself kitchen sink plumbing project before you start – you’ll save time and frustration.

  • 4 in 1 screwdriver
  • Metal saw
  • Level
  • pliers
  • Slip joint pliers
  • cord

Materials needed for this kitchen sink plumbing installation project

Avoid last-minute shopping by preparing all your documents in advance. Here is the list.

  • Basket filter
  • Cardboard washing machine
  • lock nut
  • Plumber
  • Rubber washers
  • sewing pipe
  • sewing washing machine
  • waste arms

Similar projects
How to replace a sink basket strainer Unclog a drain without chemicalsHow to replace a trash canHow to unclog a clogged drain11 pitfalls of sink replacementHow to build an undermount drawer for your kitchen brass drain assemblyHow to install crown molding on sink kitchen cabinetsHow to assemble RTA cabinetsHow to build a custom kitchen island using RTA cabinets

Popular Video Tutorials

Popular questions about how to replace under sink plumbing

How do I replace the pipe under my kitchen sink?

How do I connect plumbing under sink?

How do you replace old sink plumbing?

How much does it cost to replace a sink drain pipe?

How Much Does It Cost to Replace a Sink Drainpipe? The cost of repairing or replacing a sink drainpipe in a kitchen can be as low as $250 to $310, according to Porch.

Why is the pipe under my sink leaking?

Arguably the most common reason you’ll find water beneath your sink is that your drain has a leak in it. Shifting plumbing lines, worn-out connections, or even pipe corrosion could cause fractures in the plumbing lines beneath your sink, which cause water that flows down your drain to slowly and steadily leak out.

How do you take apart a PVC pipe under the sink?

How do you install a P-trap under a kitchen sink?

What if new sink drain doesn’t line up with existing pipes?

Move the trap into the position you need it to be under the tailpiece by pushing it to the side. If the tailpiece will not line up with the trap, move the trap into its original position, tighten the collar with the pipe wrench and obtain a flexible tailpiece extension for your drain.

How do you install an undermount sink?

What are the pipes under the kitchen sink called?

P-Trap: A P-trap is a two-part pipe under your sink that allows waste and water to pass through. The bend in the pipe prevents sewer gasses from entering. Today, most models are two pieces joined together.

How do you tell if you have a broken drain pipe?

10 Symptoms of a Damaged Sewer Pipe
  1. 1) Sewage Backups and Blockages. …
  2. 2) Sewer Gas Odor. …
  3. 3) Mold Problem. …
  4. 4) Slow Drain. …
  5. 5) Extra Green and Lush Patches in Grass. …
  6. 6) Indentation In Lawn or Under Pavers. …
  7. 7) Foundation Cracks, Settlement, and Sinkholes.

How much does it cost to replace kitchen sink plumbing?

The cost to install kitchen sink plumbing is $450 to $1,800 per fixture if new pipes and drain lines are required. The cost to replace existing kitchen sink plumbing pipes is $100 to $350 on average. Plumbers charge $45 to $150 per hour to replace pipes under a kitchen sink.

What is the life expectancy of cast iron sewer pipe?

between 50 and 100 years
Deterioration of cast iron pipes is normal after just 25 years. Wear and tear is normal in residential pipe systems. One frequently asked question is “How long do cast iron drain pipes last?” Cast iron waste pipes last anywhere between 50 and 100 years.

How do I seal the pipe under my sink?

You can fill holes around pipes under a kitchen sink (or any other sink in your home) by filling them with steel wool or copper wool and then sealing the patch with caulk, says the Centers for Disease Control and Prevention. For best results, use silicone caulk.

How do you find a leak under the sink?

Fill the sink with water, then watch underneath as it drains. Look for leakage around the slip joints in the drain pipe. Hand-tightening the large joint nuts slightly may stop leakage. If that fails, drain pipes may need to be disassembled and new joint seals installed.

Video tutorials about how to replace under sink plumbing

keywords: #ptrap, #draintrap, #replacingdraintrap, #drainpipe, #pipeforplumbing, #howto, #doityourself, #trap, #drain, #plumbing, #Drain(plumbing), #diy, #diyprojects, #kitchensinkplumbing

Subscribe and visit our weekly podcast for more tips

-https://itunes.apple.com/us/podcast/fix-it-home-improvement/id880903087?mt=2

I cover the steps to replace the kitchen sink plumbing. From the kitchen p trap and the drain pipes to the sink baskets.

You will need a pipe wrench or a large adjustable pliers to work on your under sink pipes.

If you are removing the old kitchen sink plumbing, have a bucket handy to place under the trap. You will want to remove the two nuts on the trap first and remove it. It will then be easy to unscrew and remove all the other pipes that need to be replaced.

For kitchens with two sink bowls you want to look at the main drain pipe that goes into the wall and see if it is somewhat centered, or off to one side. If this pipe going into the wall is in the center, you will want to use a center outlet kit that has two drain pipes going to one tee that is centered between them. If the main drain is off to one side then you would want to use an end outlet kit that will put the trap under one of the bowls and allow it to be lined up with the main drain.

If you are putting on new sink baskets. Put them on first and save the tail piece washer that comes with the kit. If you are keeping the old sink baskets, it is good to pick up new tail piece washers to connect the new under sink drain pipe.

To replace the drain pipes for a kitchen sink, you want to start with the small tail piece that attaches to each sink basket first. To attach this pipe to the sink basket, you will want to use a tail piece washer. This is a special washer that has a flange on one side that goes into the tail piece and a flat side that sits flush against the sink basket. If your sink basket if metal, you should use a metal nut to attack the tail piece, even if you are using plastic. If it is a plastic basket, use plastic nuts.

After attaching the tail piece to each sink basket you will connect your end or center outlet. I like the plastic drain pipe. The pipe will last a lifetime and is less expensive. I also prefer nylon washers rather than rubber washers. They last longer. On nylon washers, have the wider end toward the nut and the beveled edge going into the slip joint of the next part. When you line up your tubes that connect to the sink baskets, you will check to see if they are the correct size, if not, you will cut one of the tubes to size and tighten them down.

With your pipes attached to the sink baskets, you will now connect the wall tube to the main drain pipe going into the wall. If it is a metal pipe, use a metal nut to attach the wall tube. The wall tube is the tube that connects to the bottom part of the trap and goes into the main drain. Now that you have your wall tube in place you can see how the trap will connect between the wall tube and the tee connecting the sink baskets.

The trap can be turned and positioned to line up to both the tube coming from the sink baskets and the wall tube. If there is a gap and the tube coming from the baskets is not long enough, you will need an extension tube to connect the trap. You can cut the extension to size. If the wall tube needs to come out from the wall, you can attach an extension tube to the main drain to extend it. If you are attaching a dishwasher to the trap, you would now use a special extension with a hose fitting for the drain tube from the dishwasher. If you are connecting a dishwasher, the tube has to be above the trap.

Tighten all the nuts and check for leaks.

keywords: #SinkDrain, #DIY, #Plumbing, #DoItYourself(Hobby), #Installation, #Drain(plumbing), #Sink, #Fix, #HowtoReplaceaKitchenSinkDrain

Think about all that your kitchen sink endures on a daily basis. You put it through a lot of wear and tear, don’t you? Freshen up your Kitchen Sink with a new Sink Drain. Follow these steps to install a Sink Drain.

Subscribe to checkout our How Tos \u0026 new products »

-https://bit.ly/Dancosub

Danco Parts Finder Guide »

-https://bit.ly/DancoPartsFinder

SHOP:

AMAZON »

-https://bit.ly/AmazonDrainRepair

HOME DEPOT »

-https://thd.co/2VGsva3

RELATED PRODUCTS:

Danco Drain Repair »

-https://bit.ly/DancoDrain

Other Kitchen Sink Repair Products »

-https://bit.ly/KitchenRepair

SOCIAL MEDIA:

FACEBOOK »

-https://bit.ly/DancoFB

TWITTER »

-https://bit.ly/DancoTweet

LINKEDIN »

-https://bit.ly/DancoLinked

WEBSITE »

-https://www.danco.com

keywords: #homedepot, #homeimprovement, #diy, #howtoreplaceasinktrap, #sinktrap, #sinkplumbing, #sinkclogged, #sinktrapclogged

The curved pieces of drain pipe underneath your sink, commonly referred to as p-traps, do a lot of dirty work. Over time they leak, become corroded or get plugged with years of accumulated soap and grease. When replacing a P-trap, you should use the same type of trap you remove. Check out our plumbing playlist for more tips:

-https://thd.co/36bim8L

In this guide we’ll show you how to replace a P-trap in a few easy-to-follow steps:

-https://thd.co/2Ph1nvz

#TheHomeDepot #HomeImprovement #Plumbing

SUBSCRIBE to The Home Depot:

-http://thd.co/2iib0HE

Follow these timestamps to learn how and why to change the P-trap of your sink in a few easy steps:

0:20 Gather your materials

0:25 Remove old drainpipe

0:41 Attach new tailpiece

0:53 Add t-fitting

1:09 Attach trap arm

1:21 Connect trap bend to arm

About The Home Depot:

How doers get more done. We’re helping doers in their home improvement projects. Now you can take on more renovation projects with more know-how. Our step-by-step instructional DIY videos and expert advice will give you the confidence for your next project with hands-on learning. It’s a good time to be a doer.

WEBSITE:

-https://thd.co/TheHomeDepotSite

FACEBOOK:

-https://thd.co/TheHomeDepotFacebook

TWITTER:

-https://thd.co/TheHomeDepotTwitter

INSTAGRAM:

-https://thd.co/TheHomeDepotIG

PINTEREST:

-https://thd.co/TheHomeDepotPinterest

keywords:

See more articles in category: FAQs